Project desk: +1 800 288 6000 · [email protected]Specification support · North America

Lighting practice

Grow Light Replacement: 3 Scenarios, 3 Different Right Answers

2026-11-03 · Julian Mercer

I've answered some version of "which grow light should I replace this with?" more times than I can count—usually from operations managers who've inherited a room, a budget line, and a spreadsheet with three conflicting quotes on it. And I've stopped giving a single answer. Not because I'm being difficult, but because the right answer genuinely depends on the job in front of you.

I'm the quality and brand compliance manager at a commercial hydroponic systems integrator. I review every lighting spec and shipment before it gets installed in a client build—roughly 200 fixtures a year. In 2024, I rejected about 15% of first deliveries, mostly for spec mismatches, connector issues, and one batch where the spectrum was visibly off under our test rig. That changes how I think about the word "replacement."

Almost every lighting question I get sorts into one of three scenarios. Before you read further, figure out which one sounds like you:

  • Scenario A: You're swapping individual fixtures, one for one.
  • Scenario B: The job involves new wiring, switches, or timers.
  • Scenario C: You're building out or overhauling a full room with control and monitoring.

Each scenario has a different cost profile, rewards a different amount of planning, and hides a different trap. Here's what I've learned about all three.

Scenario A: The one-for-one swap

This is the simplest job and the most common. A fixture dies, or you're upgrading a small veg area, or—in converted spaces—you're pulling out a household-style fixture someone installed years ago and putting in something that actually grows plants. If you've ever done a replace downlight job at home, you know the drill: same cutout, same switch, new unit.

"Plug-and-play" is where people get sloppy. What actually matters for a swap: mounting footprint, driver type (and whether a replacement driver is even available), spectrum, and hanging height relative to the rest of the room.

In our Q1 2024 audit, we received a batch of 40 fixtures where the spectrum ran about 200 K cooler than spec when measured on our rig. Normal tolerance for that product line is ±100 K. The vendor claimed it was "within industry standard." We rejected the batch, they redid it at their cost, and now every contract includes a spectral measurement clause with a defined test method. That clause has saved us twice since.

For a small veg area or a propagation shelf, the Mars-Hydro TS600 grow light is the kind of unit that fits this scenario well—fixed form factor, passive cooling, no controller setup needed. What I'd flag is the TCO math on a swap. If the old fixture is four or five years old and out of warranty, replacing the driver often doesn't pencil out once you count downtime and the risk of a second failure three months later. A new unit with a warranty usually wins on total cost even when the sticker price is higher.

Trust me on this one: photograph the existing install and the label plate before you order anything. Half the replacement problems I see start with a spec sheet that didn't match reality.

Scenario B: The wiring and switch job

This is where the project stops being a swap and starts being electrical work—new circuits, wall switches, contactors, timers, subpanels. If you've been searching "how to wire a light and switch" and watching videos at 11 p.m., you're in Scenario B whether you've admitted it or not.

Here's the thing I wish more people understood: the wiring itself is usually the cheap part. The expensive parts are way more than people budget for—permits, inspection, downtime, and the electrician's minimum call-out. In my area, a mid-size US metro, a simple new circuit with a switch and a proper junction box runs a few hundred dollars as of late 2024—or rather, closer to four hundred once you add the permit fee. Add a subpanel and you're into four figures fast. Rates vary by jurisdiction, so verify with your local building department.

I had two hours to decide on a freight release last fall. Normally I'd get three quotes and sleep on it, but the cutoff was the cutoff. Went with our regular electrical contractor on trust and a phone call. In hindsight, I should have pushed the timeline a week earlier; we paid a rush premium that ate most of the savings from the fixture discount.

Two rules I've hardened into our process:

  1. Wire and switch work gets designed before fixtures are ordered, not after. The fixture choice depends on the circuit, not the other way around.
  2. Anything involving a wall switch or a new circuit goes to a licensed electrician. The DIY guides are useful for understanding what you're asking for—they're not a substitute for a permit. Per the NEC, local amendments govern, and your inspector has the final word.

Bottom line: if the quote doesn't include the electrical work, it's not a quote. It's a guess.

Scenario C: The full-room buildout with smart control

This is the scenario where the upfront number is the largest and the total cost is the lowest—if you actually use the data. Smart control earns its keep through scheduled dimming, sensor-driven HVAC triggers, and remote monitoring that catches a failing driver before it takes down a tray.

In our newer rooms we run Mars-Hydro FC-E3000 LED grow lights on Iconnect controllers, with a Zigbee sensor in each zone logging canopy temperature and humidity. The sensors are the part people skip. What I mean is: most buildouts budget generously for lights and controllers, then forget the small sensor that makes the whole system useful. A controller without sensors is just a fancy timer.

When I compared two of our rooms side by side—same genetics, same nutrient schedule, one on manual timers and one on sensor-driven schedules—I finally understood why the data matters. The automated room caught a humidity spike at 2 a.m. on a Saturday. Nobody was there. The manual room would have run the wrong VPD for six more hours.

I don't have hard data on yield lift across every crop we grow—I wish I'd tracked that more carefully from the start. What I can say anecdotally is that since we standardized on sensor-driven control in 2023, climate-related crop losses in those rooms have dropped to near zero. Plus, the fixture-level monitoring has flagged two failing drivers before they cost us a tray.

On cost: in the quotes I've reviewed for our own builds, the control layer typically adds 15–25% to the lighting line item. Spread that over a three-to-five-year depreciation cycle and it's a smaller number than most people expect. Then compare it to one lost crop, or one weekend of undetected equipment failure. From my perspective, the sensors pay for themselves the first time they catch something at 2 a.m. If you ask me, the question isn't whether you can afford smart control—it's whether you can afford to find out what happens without it.

How to tell which scenario you're in

Five questions, in order. Stop at the first "yes."

  1. Does the job involve any new circuit, wall switch, or panel work? → Scenario B.
  2. Are you lighting more than roughly 300 square feet of canopy, or do you need dimming schedules and remote monitoring? → Scenario C.
  3. Are you replacing one or two dead fixtures in an existing, working room? → Scenario A.
  4. Are you converting a non-grow space—garage, spare room, former storage—where the existing fixtures are household-style downlights or shop lights? → Scenario B, almost always, because that wiring was never designed for continuous high-load use.
  5. Still unsure? → Price it as Scenario A on paper, but get an electrician to walk the space before you order. The walkthrough is cheap. The rework isn't.

One more thing worth saying plainly: the total cost of any of these scenarios is never the number on the fixture quote. It's fixture price plus freight plus installation plus permits plus downtime plus the risk of a redo. The $500 quote that turns into $800 after setup and revision fees is more expensive than the $650 all-inclusive quote, every time—and the difference shows up on the P&L, not in the email thread.

So: figure out your scenario, price the whole job, and check the specs before you sign. The process is fairly boring, and that's exactly why it works.